FUEL METERING PUMP DEVELOPMENT AND MODELING

Jiří Toman, Vladimír Hubík, Vladislav Singule

2011

Abstract

This article would like to inform reader about the research and development steps and practices which were used during the development of a control system for a fuel metering pump. The aims of the development were to design a control system for a brushless DC (BLDC) motor in accordance with rigid aviation standards and to verify new development practices and tools allowing faster and much simpler final certification. The paper comprised definition of first requirements, preliminary hardware (HW) and software (SW) design, system modeling and simulation, system optimization, detailed design, verification and testing. In addition, the first results measured on an evaluation sample are presented.

References

  1. Bose, B. K. (2009). Power Electronics and Motor Drives Recent Progress and Perspective, IEEE Trans. On Industrial Electronics. 56, 581-588.
  2. Bose, B. K. (2009). Power Electronics and Motor Drives Recent Progress and Perspective, IEEE Trans. On Industrial Electronics. 56, 581-588.
  3. Cochoy, O. and Carl, U. B. and Thielecke, F. (2007, June). Integration and control of electromechanical and electrohydraulic actuators in a hybrid primary flight control architecture. Recent Advances in Aerospace Actuation Systems and Components, 1-9.
  4. Cochoy, O. and Carl, U. B. and Thielecke, F. (2007, June). Integration and control of electromechanical and electrohydraulic actuators in a hybrid primary flight control architecture. Recent Advances in Aerospace Actuation Systems and Components, 1-9.
  5. FAA Advisory Circulars. (2005). RTCA/DO-254 ”Design Assurane Guidance for Airborne Electronic Hardware”.
  6. FAA Advisory Circulars. (2005). RTCA/DO-254 ”Design Assurane Guidance for Airborne Electronic Hardware”.
  7. Holtz, J. (2007). Sensorless Control of Induction Machines - With or Without Signal Injection?, IEEE Trans. On Industrial Electronics. 53, 7-30.
  8. Holtz, J. (2007). Sensorless Control of Induction Machines - With or Without Signal Injection?, IEEE Trans. On Industrial Electronics. 53, 7-30.
  9. Leonhart, W. (2001). Control of Electrical Drives (3rd ed.). Berlin: Springer.
  10. Leonhart, W. (2001). Control of Electrical Drives (3rd ed.). Berlin: Springer.
  11. RTCA Inc. (1992). RTCA/DO-1'B ”Software Considerations in Airborne systems and Equipment Certification”. USA.
  12. RTCA Inc. (1992). RTCA/DO-1'B ”Software Considerations in Airborne systems and Equipment Certification”. USA.
  13. RTCA, Inc. (2007). RTCA/DO-160F ”Environmental Conditions and Test Procedures for AirborneEquipment”. USA.
  14. RTCA, Inc. (2007). RTCA/DO-160F ”Environmental Conditions and Test Procedures for AirborneEquipment”. USA.
Download


Paper Citation


in Harvard Style

Toman J., Hubík V. and Singule V. (2011). FUEL METERING PUMP DEVELOPMENT AND MODELING . In Proceedings of the 8th International Conference on Informatics in Control, Automation and Robotics - Volume 1: ICINCO, ISBN 978-989-8425-74-4, pages 419-426. DOI: 10.5220/0003530804190426


in Harvard Style

Toman J., Hubík V. and Singule V. (2011). FUEL METERING PUMP DEVELOPMENT AND MODELING . In Proceedings of the 8th International Conference on Informatics in Control, Automation and Robotics - Volume 1: ICINCO, ISBN 978-989-8425-74-4, pages 419-426. DOI: 10.5220/0003530804190426


in Bibtex Style

@conference{icinco11,
author={Jiří Toman and Vladimír Hubík and Vladislav Singule},
title={FUEL METERING PUMP DEVELOPMENT AND MODELING},
booktitle={Proceedings of the 8th International Conference on Informatics in Control, Automation and Robotics - Volume 1: ICINCO,},
year={2011},
pages={419-426},
publisher={SciTePress},
organization={INSTICC},
doi={10.5220/0003530804190426},
isbn={978-989-8425-74-4},
}


in Bibtex Style

@conference{icinco11,
author={Jiří Toman and Vladimír Hubík and Vladislav Singule},
title={FUEL METERING PUMP DEVELOPMENT AND MODELING},
booktitle={Proceedings of the 8th International Conference on Informatics in Control, Automation and Robotics - Volume 1: ICINCO,},
year={2011},
pages={419-426},
publisher={SciTePress},
organization={INSTICC},
doi={10.5220/0003530804190426},
isbn={978-989-8425-74-4},
}


in EndNote Style

TY - CONF
JO - Proceedings of the 8th International Conference on Informatics in Control, Automation and Robotics - Volume 1: ICINCO,
TI - FUEL METERING PUMP DEVELOPMENT AND MODELING
SN - 978-989-8425-74-4
AU - Toman J.
AU - Hubík V.
AU - Singule V.
PY - 2011
SP - 419
EP - 426
DO - 10.5220/0003530804190426


in EndNote Style

TY - CONF
JO - Proceedings of the 8th International Conference on Informatics in Control, Automation and Robotics - Volume 1: ICINCO,
TI - FUEL METERING PUMP DEVELOPMENT AND MODELING
SN - 978-989-8425-74-4
AU - Toman J.
AU - Hubík V.
AU - Singule V.
PY - 2011
SP - 419
EP - 426
DO - 10.5220/0003530804190426